An EV charger in a housing society does not automatically need the Electrical Inspector's approval. Under the Central Electricity Authority's safety regulations notified on 8 June 2023, the wiring must be done by a contractor licensed by your state. Installations at or below the voltage your state government has notified are then self-certified by their owner, through a Chartered Electrical Safety Engineer where your state requires one; above that voltage, the Electrical Inspector inspects. Two further checks can sit on top: the DISCOM's test when you apply for a new or additional supply, and a 30-day notice to the Inspector for buildings over 15 metres. Your state's notification sets the thresholds. This is not legal or electrical advice.

A charger is an addition to the installation

Regulation 31(1) treats "additions, alterations, repairs and adjustments to existing installations" as installation work, so a wall-box, a new circuit to a parking bay or a society pedestal is an addition to someone's installation: your flat's if it hangs off your meter, the society's if it hangs off the common supply. What the charging point itself must have is a separate chapter, Chapter XI (regulations 123 to 128), which applies "in addition to the regulations provided from chapter I to VII" and is not covered here; practical checks before first use are on our safety checklist.

The licensed contractor and the supervisor

Unless another source is named, every rule here comes from the Central Electricity Authority (Measures relating to Safety and Electric Supply) Regulations, 2023, notification No. CEA-PS-16/1/2021-CEI Division dated 8 June 2023, in force from publication in the Gazette of India. We read the Gazette PDF through its archived copy of cea.nic.in; last verified 16 October 2026.

Regulation 31(1) allows installation work only "by an electrical contractor licenced in this behalf by the State Government and on its behalf under the direct supervision of a person holding a certificate of competency and by a person holding a permit issued or recognised by the State Government". That is three credentials, and your quote should name all three:

  • the contractor's licence, issued by your state;
  • the certificate of competency of the supervisor on the job;
  • the permit of the person doing the wiring.

The exception covers replacing "lamps, fans, fuses, switches, domestic appliances of voltage not exceeding 250 V and fittings as in no way alters its capacity or character". A new circuit to a parking bay alters capacity, so it is not a replacement. Plugging a portable charger into an existing socket reads as using an appliance rather than installation work, though the regulation does not say so in terms; whether that socket can take hours of continuous load is for a licensed electrician to judge (portable unit or wall-box).

Regulation 31(2) adds the consequence: "No electrical installation work which has been carried out in contravention of sub-regulation (1) shall either be energised or connected to the works of any supplier." Regulation 31 decides who may do the work; what the circuit, protective devices and earthing should be must be specified and certified by a licensed electrician, and nothing here is electrical advice. A state may exempt a class of work by Gazette notification, so if an installer says no licence is needed, ask which notification says so. Put the three numbers beside the line items in our quote comparison; what the electrician inspects is in the site assessment.

The DISCOM's test before new or additional supply

Regulation 33(1) applies "Upon receipt of an application for a new or additional supply of electricity and before commencement of supply". The DISCOM "shall either test the installation himself or accept the test results submitted by the consumer when same has been duly signed by the licenced electrical contractor". At or below the notified voltage, a Chartered Electrical Safety Engineer "can also test the installation on request of owner".

A separate EV connection is new supply. A load enhancement reads naturally as additional supply, though the phrase is not defined, so ask the DISCOM in writing whether it will test or accept contractor-signed results. If the charger fits within your existing sanctioned load and you apply for nothing, regulation 33 is not triggered on its words; whether you must apply is covered in sanctioned load and load enhancement.

Two duties fall on the DISCOM at connection. Regulation 35(1) requires leakage to be checked "by measuring the installation's or apparatus' insulation resistance as stipulated in the relevant standards", and if it declines, regulation 35(2) says it "shall convey to the applicant the reasons thereof, in writing". Where it finds the installation "likely to be dangerous", regulation 33(5) has it serve "a notice in writing requiring him to make such modifications as are necessary" and lets it refuse until they are made.

  1. Attach test results signed by the licensed contractor to the application.
  2. If field staff decline to connect, ask for the reasons or the modification notice in writing. A verbal "not okay" is not what either regulation provides.
  3. Give the written reasons to your licensed electrician, rectify, and resubmit with freshly signed results.

Self-certification up to your state's notified voltage

Regulation 2(1)(zu) defines "notified voltage" as one "notified by the Appropriate Government under intimation to the Authority for the purpose of specifying the voltage level up to which self-certification is to be carried out under regulation 32 and regulation 45". For a building in a state, that is the State Government, under section 2(5)(b) of the Electricity Act, 2003, so no national figure answers this. Nor is the test a charger's kilowatt rating: regulations 32 and 45 turn on voltage.

Regulation 45(1)(a) says "Every electrical installation of notified voltage and below shall be inspected, tested and self-certified by the owner or supplier or consumer" before supply commences, with the report sent "to the Electrical Inspector in the forms as provided under Schedule II". Above it, regulation 45(3) requires the Inspector's inspection; at or below it, the second proviso to 45(1)(a) keeps your "option to get his installation inspected and tested by the Electrical Inspector".

For additions, regulation 45(6) says the owner "shall not connect to the supply" an alteration or addition "unless and until such alteration or addition has been approved in writing by the Electrical Inspector or self-certified by the owner of the installation". One caveat: regulation 45 sits in Chapter VI, headed "Safety provisions for electrical installations and apparatus of voltage exceeding 650 V", yet its text reaches installations "of notified voltage and below" and points to Form I, which covers up to 250 V. Whether 45(6) reaches a 230 V charger added in a flat is not settled by the text; ask your state's Electrical Inspectorate in writing rather than assume either way.

The installation counts as fit "only after the report of self-certification is duly received by the office of Electrical Inspector and if not acknowledged by the Electrical Inspector within three working days, it shall be deemed to be received". Suppose you file on Monday 2 November 2026 and hear nothing. Counting from the day after filing, which is our reading because the regulation does not say, the three working days are Tuesday 3, Wednesday 4 and Thursday 5 November, so by the close of Thursday the report is deemed received. If one of those was a holiday at that office, skip it; the regulation does not define a working day either, so keep a dated receipt or portal timestamp. This proviso is written for commencement of supply; regulation 45(6), on additions, sets no clock of its own.

One class never self-certifies. Regulations 45(1)(b) and 32(4) keep "every electrical installation covered under section 54 of the Act" with the Inspector. Section 54(1) of the Electricity Act, 2003 (No. 36 of 2003, assented to on 26 May 2003) covers using electricity above "two hundred and fifty watts and one hundred volts" in a street, factory or mine, a place the state declares, or a place "in which one hundred or more persons are ordinarily likely to be assembled". Anyone other than a transmission utility or licensee using electricity in such a place must also give "not less than seven days' notice in writing" to the Electrical Inspector and the District Magistrate or Commissioner of Police before starting. Whether a society's common areas are such a place, the Act does not say; a dispute over the hundred-person test goes, under section 54(2), "to the State Government, and the decision of the State Government thereon shall be final". We read the Central Electricity Regulatory Commission's consolidated text, archived at web.archive.org; last verified 16 October 2026.

Form I, II or III: picking the right one

Schedule II, "Forms of Inspection Report [See regulation (32) and (45)]", sorts reports by voltage. Form IV is for mines, so an apartment uses one of these:

FormBand, as printed on the formApartment set-up it fits (our reading)
Form I"Installations of voltage up to and including 250V"A single-phase flat connection, and a private point fed from it
Form II"Installations of voltage level more than 250 V up to and including 650 V"A three-phase flat connection, or a society's three-phase common supply
Form III"Installations of voltage exceeding 650 V"A society taking high-voltage supply through its own transformer

Read the voltage and phases from your bill or connection papers, not the charger's label. The voltage between the phases of a three-phase supply is above 250 V, which is why a three-phase flat lands on Form II; if unsure, ask your electrician.

Form I asks for the consumer number, voltage, phases, wiring type, points and "Other equipment" with their connected load, and "Maximum current demand in Amps", then a checklist keyed to regulation numbers: overloading, earthing, insulation resistance in "Mega Ohms", and whether a "residual current device of appropriate capacity" is fitted under regulation 44 (RCCBs and RCBOs explained). Each answer should come from a test your electrician performed; a form filled from memory certifies nothing.

The connected-load line is one sum you can check. Suppose your last Form I, or your electrician's survey, shows 6.4 kW connected and you add a charger rated 3.3 kW; substitute your own figures. The new total is 6.4 + 3.3 = 9.7 kW. That declares what is connected; it does not change your sanctioned load, which is the DISCOM's separate question.

Each form ends with "Signature of the supplier/ Owner / Consumer", so the person certifying is you for your flat, or the society for its common installation. After Form III the schedule prints a certificate "For Self-certification by supplier /owner /consumer", stating the installation "is complete in all respects" and "electrically safe to operate", with "Encl: Test reports" and two signature lines: "Self-certifying supplier / owner / consumer" and "Chartered Electrical Safety Engineer". The text does not say whether that certificate travels with Forms I and II; your state's format or portal decides.

Chartered Electrical Safety Engineers

Regulation 6(1) has the government authorise these engineers "from amongst persons having the qualification and experience as per the guidelines issued by the Authority to assist the owner or supplier or consumer of electrical installations for the purpose of self-certification under regulation 32 and regulation 45". Regulation 6(2) requires each name to be uploaded "on the web portal of the Government or the Department dealing with matters of inspection of electrical installations".

Whether the engineer is compulsory is for your state's notification; Odisha's, below, routes self-certification "through certified Chartered Electrical Safety Engineers (CESEs) as opted by the owner/supplier/consumer".

  • Check the name against the state portal list before engaging anyone.
  • Ask for the authorisation number on the quote, beside the contractor's licence number.
  • Decide whether you want the engineer independent of the contractor. The regulations do not address it, and we have not read the Authority's qualification guidelines that regulation 6(1) refers to; a second pair of eyes is the reason to choose it.
  • The engineer assists; the self-certification remains the owner's statement.

Buildings above 15 metres: the 30-day notice

Regulation 38(1) says "The connected load and voltage of supply above which inspection is to be carried out by an Electrical Inspector for a multi-storeyed building of more than fifteen metre height shall be notified by the Appropriate Government." Under regulation 38(2), before "making an application for commencement of supply or recommencement of supply after an installation has been disconnected for a period of six months or more", the owner or occupier "shall give not less than thirty days notice in writing to the Electrical Inspector specifying therein the particulars of installation", and supply "shall not be commenced or recommenced within this period, without the approval in writing of the Electrical Inspector".

Regulation 38(2) sets no load or voltage floor of its own: on its words it binds the owner or occupier of any such building. Whether your state reads it with its 38(1) figures, so that smaller installations escape the notice, is a question to put to the Inspectorate in writing, not to assume. It also speaks only of commencement and recommencement, not additions, so a charger on a flat's existing connection is, on its words, neither. A new separate EV connection in an occupied tower is the open case: it commences supply to a new installation, but whether regulation 38(2) means that, or only a building's first supply, the text does not say. Ask the Inspectorate in writing before you apply to the DISCOM.

If it applies, notice comes first and the application second. Suppose the Inspector's office receives your notice on Monday 2 November 2026: thirty days on is Wednesday 2 December 2026, and supply should not begin before then unless the Inspector approves in writing. Count from a receipt date you can prove.

The regulation does not say how height is measured, so take it from the building's sanctioned plan. Regulation 38(3)'s wiring measures for these buildings are a separate subject. Maharashtra's fire and building texts on basement charging are another authority again, covered in our basement and podium guide.

Periodic self-certification, disconnection notices and appeal

Regulation 32(1) sends periodic inspection above the notified voltage to the Inspector, while installations "below or equal to the notified voltage shall be self-certified by the owner or supplier or consumer". Regulation 32(2) leaves the interval to the government, "Provided that the periodicity of electrical inspection and self-certification shall not exceed five years". Regulation 32(3) asks for the report in Forms I to IV, with the same deemed receipt after three working days.

Suppose your society's common installation was last self-certified on 15 March 2024; substitute your own date. Five years on is 15 March 2029, the latest the national cap allows; if your state sets three years, it is 15 March 2027. The duty belongs to each installation's owner: the flat's consumer for a private point, the society for its common supply. Regulation 32(8) makes it "the responsibility of the owner of all installations to maintain and operate the installations in a condition free from danger".

Large societies have one more figure. Under regulation 5(3), "For every electrical installation including factory registered under the Factories Act, 1948 (63 of 1952) with more than 250 kW connected load", the owner "shall designate Electrical Safety Officer", a qualified engineer who must "inspect such installations at intervals not exceeding one year". Whether a society's common installation is caught, the wording does not settle. Suppose your Form II shows 190 kW connected and you plan six chargers rated 11 kW each; substitute your own figures. 190 + 6 × 11 = 256 kW, over 250, so ask the Inspectorate in writing before ordering.

Regulation 32(7) ties disconnection to unrectified defects, not to a late or missed form (we have not traced what follows from one): an owner who fails to rectify defects "pointed out by the Electrical Inspector in his report and within the time indicated therein" is "liable to be disconnected under the directions of the Electrical Inspector after serving the owner of such installation with a notice for a period not less than forty eight hours". The proviso protects you only where "an appeal is made under sub section (2) of section 162 of the Act and appellate authority has stayed the orders of disconnection". Separately, regulation 36(2) lets the supplier cut supply where, after a notice to test, the consumer refuses access or insulation resistance is too low for safe use, "only after giving to the consumer forty eight hours notice in writing".

Section 162(1) of the Electricity Act, 2003 lets the state appoint a "Chief Electrical Inspector or Electrical Inspectors", the office the abbreviation CEIG refers to, and section 162(2) says "an appeal shall lie from the decision of a Chief Electrical Inspector or an Electrical Inspector to the Appropriate Government or if the Appropriate Government, by general or special order so directs, to an Appropriate Commission". Forty-eight hours is short: act the day the notice arrives, and take an advocate's help with any appeal.

  1. Have your licensed electrician rectify and document every listed defect within the time allowed.
  2. If you dispute the decision, appeal to the State Government, or the Commission if your state so directs, and ask for a stay at once; only a stay stops disconnection.

Three walkthroughs: private point, society charger, separate EV connection

StepPrivate point on the flat's connectionSociety charger on common supplyNew separate EV connection
Who does the work (reg. 31)Licensed contractorLicensed contractorLicensed contractor
DISCOM test (regs. 33, 35)If you apply for more load (read as additional supply)If the society applies for more load (same reading)Yes, before connection
Who certifies (regs. 32, 45)You, at or below the notified voltage; whether 45(6) reaches a flat addition is unsettledThe society; the Inspector above it, or under section 54The applicant, at or below the notified voltage
FormI if single-phase, II if three-phaseII on LT supply, III on HT supplyI or II by phases
30-day notice (reg. 38(2))Not on its wordsNot on its wordsOpen question in a tower over 15 m
Periodic duty (reg. 32)YouThe societyThe connection holder

A private point on your flat's own connection

Ask the Inspectorate whether it expects a regulation 45(6) self-certification for the addition; if so, that is Form I for a single-phase flat, signed by you on your electrician's results; keep proof of the filing date, since 45(6) sets no acknowledgement clock of its own. Society permission is a separate question (requesting permission; what the law settles). File the result with what to keep in the charger file.

A society charger on the common supply

The society is the owner, so an office-bearer it authorises signs, and the authorising resolution should name who. On HT supply through its own transformer, Form III is self-certified or inspected depending on where your state's notified voltage sits. Settle the section 54 question early and in writing, because if the Inspectorate treats the common area as a section 54 place, self-certification is off the table. The proposal is covered in proposing a common station; the society's file should follow what to keep in the charger file.

A separate EV connection for one resident or the society

This is new supply, so regulations 33 and 35 apply in full. At or below the notified voltage, regulation 45(1)(a) has it self-certified before commencement, on Form I or II, subject to the Chapter VI caveat above. In a tower above 15 metres, settle the regulation 38(2) question before filing the application. Whether a separate connection suits you is a metering question (own meter, sub-meter or common meter); keep the papers as set out in what to keep in the charger file.

Finding your state's notification: the Odisha example

Everything above turns on figures only your State Government supplies: the notified voltage (regulation 45(2)), the tall-building connected load and voltage (38(1)) and the inspection interval (32(2)). Find the current notification and copy its number and date into your file.

The Government of Odisha, Energy Department, issued Notification No. 5728/En "in exercise of the powers conferred under Sub-regulation (1) of Regulation 38 and Sub-regulation (2) of Regulation-45", "in supersession of all previous orders/instructions issued in this regard", "with immediate effect". The date is handwritten on the scan as 26/05/2026, matching the signature. Memo No. 5729 of the same day forwarded it with a request to publish it in the Odisha extraordinary gazette; we did not locate that issue, so we cite the department's upload at energy.odisha.gov.in; last verified 16 October 2026.

What to copy from your state's notificationWhat Odisha's No. 5728/En says
Number and date5728/En, dated 26/05/2026 by hand
Powers citedRegulations 38(1) and 45(2)
Self-certification voltageInstallations "at voltage up to 33 kV shall be self-certified"
Who certifiesThe owner, supplier or consumer, "through certified Chartered Electrical Safety Engineers (CESEs) as opted by the owner/supplier/consumer"
Always the InspectorSection 54 installations, mines, oil fields and railways, "irrespective of voltage level"
IntervalNotification No. 10317 dated 27.10.2022 "shall continue to be in force" (we have not read it)
Tall-building connected loadRegulation 38(1) is cited, but no connected-load figure is stated

On its words, a flat or society in Odisha supplied at or below 33 kV self-certifies through a certified engineer, unless section 54 applies. Whether "as opted by" lets you choose which engineer, or whether to use one at all, the text does not say; ask the Inspectorate.

  1. Search your state Energy or Power Department's notifications, and the Electrical Inspectorate's site, for "Regulation 45" or "notified voltage".
  2. Check it is current, then copy its number, date, voltage, any engineer requirement and interval reference into your file.
  3. Find the state's engineer list published under regulation 6(2).
  4. If you find nothing, write to the Inspectorate asking for the figures under regulations 45(2), 38(1) and 32(2), and keep the reply.

Common questions

Does a home EV charger in my flat need the Electrical Inspector's approval?

Not automatically. At or below your state's notified voltage, the route is self-certification on a licensed contractor's test results, through a Chartered Electrical Safety Engineer where your state requires one; whether an addition inside a flat needs a filed certificate at all is unsettled, so ask the Inspectorate. The Inspector comes in above that voltage, for section 54 installations, during a tall-building notice period, or if you choose the Inspector.

Is "CEIG approval above 10 kW" a real rule?

CEIG points to your state's Chief Electrical Inspector, appointed under section 162(1) of the Electricity Act. We found no 10 kW figure in the CEA safety regulations; the thresholds are a voltage notified under regulation 45(2) and, for buildings over 15 metres, a connected load and voltage notified under regulation 38(1), both by your state. The only connected-load figures we found, in regulation 5(3) (250 kW, and 2000 kW for mines and oil-fields), decide when an Electrical Safety Officer must be designated, not the Inspector's approval. Ask whoever quotes a kilowatt figure for the notification number.

Can our society's maintenance electrician fit the charger?

Only as part of a licensed contractor's job. Regulation 31(1) requires a state-licensed contractor, a supervisor with a certificate of competency and a worker with a permit, and regulation 31(2) bars energising work done otherwise.

What if the Inspector's office never acknowledges my self-certification?

Unacknowledged after three working days, it is deemed received under regulations 32(3) and 45(1)(a). Keep proof of the filing date; on our reading, count the office's working days from the next day, since the regulations do not say.

Can the DISCOM refuse to connect after testing?

Yes, if it finds the installation likely to be dangerous or its insulation resistance unsafe. Regulation 33(5) requires a written notice of the modifications needed, and regulation 35(2) written reasons for declining.

Does self-certification mean the installation is safe?

No. It is the owner's signed statement built on a licensed electrician's tests, and regulation 32(8) leaves the owner responsible for keeping the installation "free from danger".